Lighting Services

EMERGENCY LIGHTING INSTALLATION AND MAINTENANCE SERVICES IN LONDON AND HERTFORDSHIRE

Anco Electric are fully NICEIC trained and approved installers on Emergency Lighting. We can test and maintain current emergency lighting installations for commercial properties, services offices, retail outlets and communal areas in residential blocks/apartments, as well as the design of emergency lighting systems for various applications

Our typical emergency lighting maintenance service involves the following:

  • An annual 3 hour drain down test
  • A routine periodic emergency lighting report.
  • A 1 hour Emergency lighting test at 6 monthly intervals.
  • Staff training for monthly emergency lighting flick test, which is required to ensure batteries and light fittings are operational.
  • To issue, set up and train staff members in how to use an emergency lighting log book.

Emergency Lighting is essential in the event of a fire or power failure, and enables customers, staff and visitors to find emergency escape routes and exits should the need arise

Why Choose Anco Electric for Emergency Lighting Services?

Anco Electric offers a complete emergency lighting service, taking the bulk of the responsibility away from businesses, estate agents and chartered surveyors alike. We offer annual emergency lighting packages, which offer on-hand expertise, cost savings and a professional service. Anco Electric are NICEIC approved and our engineers are all trained and specialist emergency lighting technicians.

Anco Electric are specialists in emergency lighting:

  • Fully Trained NICEIC Emergency Lighting Installers
  • Fully Trained NICEIC engineers for emergency lighting maintenance
  • Anco Electric are a NICEIC Approved Contractor
  • Anco Electric are an Approved Safe Contractor
  • £5 million in public liability

What Happens on Annual Electrical Lighting Inspections?

1. We Identify the type of fittings installed

Maintained fitting – will operate as a normal light fitting and be controlled with all the other lights in the area, however when the power fails the maintained emergency fitting will continue to operate but at a lower light level.

Non-maintained fitting – is normally switched off, with its batteries being continuously charged and a green LED indicator. When the power fails, the fitting switches on using its battery supply. Non-maintained fittings are not part of the general lighting but are fittings such as emergency exit signs.

Combined emergency luminaire – a luminaire containing two or more lamps, at least one of which is energised from the emergency lighting supply and the other(s) from the normal lighting supply. A combined emergency luminaire can be either maintained or non-maintained.

2. We identify what type of Emergency Lighting has been installed and where it’s needed

Emergency escape lighting – the part of an emergency lighting system that provides illumination for the safety of people leaving a location or attempting to terminate a potentially dangerous process beforehand. It is part of the fire safety provision of a building and a requirement of The Regulatory Reform (Fire Safety) Order 2005.

Standby lighting – the part of an emergency lighting system provided to enable normal activities to continue substantially unchanged. This guide does not include standby lighting as it is not a legal requirement and is a facility that may or may not be needed, depending on the use and occupancy of the premises, etc.

Emergency escape lighting is subdivided into escape route lighting, open area lighting and high risk task area lighting.

Escape route lighting – that part of an emergency escape lighting system provided to ensure that the means of escape can be effectively identified and safely used by occupants of the building.

Open area lighting (anti-panic lighting) – the part of an emergency escape lighting system provided to minimise panic and ensure there is sufficient illumination to allow the occupants of a building to reach a place where an escape route can be identified.

High risk task area lighting – the part of an emergency escape lighting system that provides illumination for the safety of people involved in a potentially dangerous process or situation and to enable suitable shut-down procedures for the safety of the operator and other occupants of the premises.

3. Undertake a full duration test

To test an emergency lighting system, it is important to simulate emergency conditions or mains failure on lighting and emergency lighting circuits. The idea of this is to activate the emergency lighting system to operate via the battery supply. This test can be carried out manually or automatically.

A full drain down test for the full rated duration of the emergency lights (e.g. 3 hours) must be carried out. The emergency lights must still be working at the end of this test. The result must be recorded in both an emergency log book and an emergency periodic inspection report and, if failures are detected, these must be remedied as soon as possible.

ANCO ELECTRIC

Serving the Tristate Area

Schedule now